Other

It seems so small and insignificant, yet it's so important. The BB30 Wave Spring Washer is the keystone in your bottom bracket assembly, providing compression for proper setup and bearing preload, while helping to maintain adjustment after it's dialed in just right. They're also quite easy to lose or damage, so grab a few while you're at it.

- Aluminum straddle cable carrier for cantilever brake

Problem Solvers has a couple different options for adding cable housing or brake hose guides to your bike. Choose from the adhesive stick-on option or the guide that mounts to existing housing stops.

Original equipment replacement rear derailleur hangers. Get back on the road with a quality replacement hanger. Product details - Attachment hardware is sold separately - For specific compatibility concerns, please contact our Customer Service team Specifications - Mounting location: Rear drive side - Attachment: 1-bolt

Lip-Locks secure your seatpost and add functional bling to your ride. - Non-quick release version of the Flip-Lock - Machined 6061-AL with stainless steel pivot and bolt - Anodized with laser-etched logo - For smooth operation, lightly grease the bolt threads

The 12mm slotted MDS dropout is the newest chip for Surly's MDS equipped trail frames. You like chips, don't you? The 12mm slotted dropout chip uses a standard derailleur mount for maximum compatibility and is made of cast and machined 6061-T6 aluminum, with a fender eyelet. What's the coolest part about the 12mm slotted MDS chip, you ask? The fact that it also has the capability to run a 12 x 142mm thru-axle in a single speed configuration. This is good news because single speeds are good news. When you get an MDS equipped frame you're getting the option to set it up however you want. You can run a 142 x 12mm thru-axle rear end with a direct mount Shimano hanger, standard 135mm QR or The Mighty Singlespeed. The way this will work is that Surly complete bikes that feature the MDS will ship with whatever chip is compatible with derailleur spec. For instance, the complete Instigator 2.0 ships with the 142 x 12mm thru-axle Shimano chip. If you want to change it to a singlespeed later (and why wouldn't you?), all you have to do is get the SS chip. Frames will ship with all three MDS chips so pick your poison. The 142 x 12mm and 135mm QR chips are made of cast and machined 6061-T6 aluminum and The Mighty Singlespeed chip is 304 stainless steel, because the two words 'aluminum' and 'singlespeed' should never be too close to each other. Bad things can happen…. As you can see, the MDS gives you not just different build options, it lets you use a more varied selection of parts for your frame up builds. The MDS is featured on most of our trail bikes. That's right: Krampus Ops, Karate Monkey Ops, Instigator 2.0 and Ice Cream Truck frames all sport these puppies.

- Replacement retaining clip for the Surly Tuggnut/Snuggnut

Surly Thru-Axles are low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Offered in several sizes, for both front and rear wheels. 12x142 Rear Thru Axle: - Fits: Midnight Special and MDS Dropout bikes including Instigator, Legacy Karate Monkey & Legacy Krampus. 12x142/148 Rear Thru Axle: - Designed for frames with Surly Gnot Boost spacing (145mm), capable of working with 142 or 148mm rear hubs - Fits: Karate Monkey, Krampus, Troll, Ogre, ECR 12x177 Rear Thru Axle: - Fits: Wednesday 12x197 Rear Thru Axle: - Fits: Ice Cream Truck, Big Fat Dummy 12x100 Front Thru Axle: - Fits: Midnight Special 15x110 Front Thru Axle: - Fits: Karate Monkey, Krampus 15x150 Front Thru Axle: - Fits: Wednesday, Ice Cream Truck, Big Fat Dummy

Surly Mr. Whirly Spindles. - 100% CroMoly steel - Proprietary dimensions and spline for use only with Surly Mr. Whirly cranks

Rear disc brake adaptor specifically designed ONLY for the Surly Troll, Ogre and ECR. - For use with 160mm rotor only - Brake caliper must be 74mm post mount compatible

The Problem Solvers Chain Tensioner is a handy device that lets you cleanly install a derailleur on frames without a derailleur hanger. It's made of light and durable CNC-machined 6061 aluminum with steel hardware. It's designed for use with rear-facing horizontal dropouts and 10mm rear axles.

ReMatch adapters are designed to integrate different generations of Shimano Brakes to Shimano Shifters. Rematch Adapter 1.2 connects Shimano I-Spec A/B brake to I-Spec II Shifter. - Made from CNC Machined T6061 Aluminum - Anodized Black - Includes all necessary hardware for both I-Spec A and I-Spec B brake - No additional hardware needed

Switching frames doesn’t mean you have to switch posts! Use your old posts without worry with Problem Solver's wide variety of seatpost shims. -100mm long -3mm lip -Alloy Problem Solvers Seatpost Shims are not intended for use with carbon seatposts

Downtube cable adjusters from Problem Solvers. - Braze-on downtube adjusters for road shifters - Contoured to fit traditional sized steel downtubes - Black Finish

The Problem Solvers Double Chainring Bolts include 5 chainring bolts and nuts that are 8mm wide. This is the right size for most double-chainring setups. These chainring bolts are made of aluminum and feature dual-hex heads for easy, secure installation.

Available in the most common sizes and thicknesses-in small or bulk quantities, Problem Solvers headset spacers help riders get their stack height just right. - Made from Aluminum, anodized or polished finish, without logos - S.H.I.S. Stem Clamp Diameter: 25.4mm

The Problem Solvers Travel Agent amplifies your braking power so that you can mix road, mountain and cyclocross brakes and brake levers. Instead of buying new levers or brakes, just install a Travel Agent and you're good to go. This trick gizmo is made of quality 6061 aluminum and is available with and without a built-in adjustment barrel. It works with cantilever brakes, road dropped handlebars, and Shimano STI and Campagnolo Ergopower levers.

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Service Kit - 3-Pawl

RockShox Vivid/Kage Rear Shock Springs - Coil springs are available in many sizes and weight ratings - Each are available separately and are not included with Vivid and Kage aftermarket shocks

RockShox Vivid/Kage Rear Shock Springs - Coil springs are available in many sizes and weight ratings - Each are available separately and are not included with Vivid and Kage aftermarket shocks

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss 18t Superlight Star Ratchet Kit: Includes Springs and Grease

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Star Ratchet Kit - 36T

ZIPP Service Course Bar End Plugs, Qty 2.

Zipp Speed Weaponry Vuka Aero Center Cap Kit - Bolt kit sold separately

Zipp Speed Weaponry Vuka Extension End Plugs - Plastic bar end plug pair for 22.2mm extensions

Vuka Alumina Clip Risers are designed for use with the Vuka Alumina Clip's above-bar option. The risers are designed to offer a wider range of adjustability within the Vuka Alumina aero-cockpit system.

- Self Extracting crank bolt Suitable for: - Road: Powerbox alloy, Powerbox Supercompact alloy, Energy, Gossamer cranksets - Off-road: Powerbox alloy, KFX, Gradient cranksets

Keep that front end tight and responsive, while preserving the integrity of the carbon steerer on your high-end fork with FSA's Headset Compression Plug. - Alloy top cap - For carbon steer tubes

Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks

The tool-free Maxle Ultimate Rear brings exceptional stiffness and durability to your ride in a high clamping force, easiest-to-use internal cam thru axle system.

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Shimano's Di2 Battery Charger Cable plugs into the Battery Charger (shown, but sold separately) so you can keep your electronic drivetrain at full power.

Hellbender bearings have an improved seal structure and are cross compatible with Cane Creek headsets.

110-Series Alloy Interlok Headset Spacer - Aluminum construction

Seal replacement kit for Jade model rear shocks.

Elastomers are designed for use with eeSilk or eeSilk+ seatposts, featuring different durometers that provide different levels of comfort. - Cane Creek eeSilk+ Elastomer 1 - 40 Durometer, X-Soft

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

105 piece assortment of 1-1/8" aluminum headset spacers

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

Alex Kennedy's signature sprocket pairs an 8mm thick sprocket with a 10mm thick replaceable nylon/fiberglass guard. - 6061-T6 alloy, full CNC sprocket and nylon/fiberglass replaceable guard - Runs directly on 24mm spindle - Supplied with adaptors for 19mm & 22mm spindles - Sinked adaptor for better chain alignment - Super durable, replaceable nylon/fiberglass guard allows for friction free grinding

The new range of extensions have evolved from our well proven T-Series. They have been designed to offer distinct fit options. We have also adopted a new naming system whereby the name gives the angle material of the extension. Thus 35a is a 35° bend in aluminum. Performance - The sole purpose of extensions is to provide a comfortable position for the riders hands relative to the armrests. They enhance performance by allowing the rider to relax into their optimal position. Which is why we provide different fit options so each rider can chase their best performance. Fit Data - Extension Shape: A 35 degree ski-bend extension suited to riders who prefer to adopt a wrist angle that is on the low side of the neutral range. - The 35a is a straight 35° bend. Tech Guide - All the extensions have a 22.2mm diameter in the clamping area. - They are designed for cables to be routed out the rear of the extensions so do not have cable exit holes. Who is it for? - The extensions will fit in any aerobar that is designed for 22.2mm. So can be used by any rider wishing to improve the comfort of their aerobar grips. - Length: 340mm or 400mm - Outer Diameter: 22.2mm - Construction: 6061-T6 aluminum, pre-drilled for bar-end shifter cable routing - Weight: 200g/pair

Pro Compressionless brake housing eliminates flex from cable actuated braking systems, increasing power and improving lever feel. - KEB-SL - linear strand, Kevlar reinforced, compressionless brake housing with Slick-Lube liner - Perfect for full-housing, high-performance bikes with mechanical disc or rim brakes - 20 black alloy lined end caps, 10 black POP end caps included

Wheels Manufacturing Clear Chainstay Protectors keeps your frame's paint looking good and helps quiet any chain slap on the chainstay. Pack of 10

Replacement spacer pack for Wheels Mfg. 24mm (Shimano) bottom brackets. Bearings sold separately. Pack Includes: - (2) - Silicone Dust Seal, 24mm ID - (2) - 0.5mm, 24mm ID Crank Spindle Spacer - (2) - 1.0mm, 24mm ID Crank Spindle Spacer

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements

Protective pad for your chainstay prevents damage and scratches. - Soft pad with Race Face logos

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 2737 Bearing for 240s Predictive Steering Hubs

The absoluteBLACK's HOLLOWcage® for Shimano 9100 and 8000 derailleurs makes the 9100 and 8000 drivetrains whisper quiet. It features a carbon-polymer mono-plate construction with bespoke, oversized, full ceramic bearings and one of the most advanced silencing pulleys ever made. - Designed for use with Shimano Dura-Ace 9100 / 9150 / 9170 , and Ultegra 8000 / 8050 drivetrains - Fits up to a 32t cassette - The Silent Xring Pulley dampens the chain impact on the guide pulley teeth, eliminating the engagement noise - Incredibly silent (over 12dB noise reduction vs stock) - HOLLOWcage uses full ceramic bearings (Silicon Nitride ceramic balls and Zirconia Oxide ceramic races) that make the guide pulleys incredibly stiff for greater shifting precision - Upper pulley features tall teeth to provide improved shifting precision - One of the lightest oversized cages on the market (71g) - Not compatible with Ultegra Long GS cage derailleurs

Adjustable spring rate coil that's also progressive. Sprindex is specifically designed to have a progressive spring rate for the last 20% of stroke for big hit support and for bikes with a linear linkage design. - Adjustable spring rate - Adapters included for different size shocks and set ups - Made of super high tensile spring steel

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Aluminum headset stack spacers precision-cut to ensure proper headset function. - Precision-cut for proper function - Inner Diameter: 28.9mm - Outer Diameter: 34.4mm - Precision-machined aluminum

You have to get that handlebar height just right. It's more comfortable, more efficient, and helps keep your entire upper body healthier. Wheels Manufacturing has your well-being covered with a wide variety of sizes to ensure your bars are right where they need to be. - Spacers are sold individually or in packs of 5 or 10 spacers. Select options from the dropdown menus to display pack size

- Alloy construction - Great for Cruiser or BMX bar conversions

- 10-speed: stainless steel 6.1mm wide no tool chain connector for Shimano and Campagnolo - 9-speed: stainless steel 6.5mm wide no tool chain connector for Wippermann chains - 6-8 speed: stainless steel 6.8mm wide no tool chain connector for Wippermann chains